Comments for Electronics Area https://electronicsarea.com Electrical and Electronics Tutorials and Circuits Fri, 29 Dec 2023 18:22:51 +0000 hourly 1 https://wordpress.org/?v=4.9.25 Comment on Audio Splitter Circuit Diagram – 1 Input – 4 Outputs by Marcel https://electronicsarea.com/1-input-4-outputs-stereo-audio-splitter/#comment-451494 Fri, 29 Dec 2023 18:22:51 +0000 http://electronicsarea.com/?p=3493#comment-451494 Hi Richard

You need 2 sets of audio splitters to get a complete stereo system.

Greetings

]]> Comment on Audio Splitter Circuit Diagram – 1 Input – 4 Outputs by Richard Mahinske https://electronicsarea.com/1-input-4-outputs-stereo-audio-splitter/#comment-451258 Wed, 27 Dec 2023 23:01:30 +0000 http://electronicsarea.com/?p=3493#comment-451258 Why do you list 8 of everyhting and only show 4 of each in the circuit diagram?

]]> Comment on Audio Splitter Circuit Diagram – 1 Input – 4 Outputs by Marcel https://electronicsarea.com/1-input-4-outputs-stereo-audio-splitter/#comment-407955 Mon, 08 May 2023 18:37:54 +0000 http://electronicsarea.com/?p=3493#comment-407955 Hello.

Yes, you can, but you won’t have a way to control the volume of the amplifier output. I think it is better to leave the circuit as it is and set the volume to the desired level.

Hope this help you.

]]> Comment on Audio Splitter Circuit Diagram – 1 Input – 4 Outputs by cederic bosvelt https://electronicsarea.com/1-input-4-outputs-stereo-audio-splitter/#comment-388137 Tue, 03 Jan 2023 15:08:21 +0000 http://electronicsarea.com/?p=3493#comment-388137 can i use resistors instead of a potentiometer?

]]> Comment on Continuity tester using 741 IC by Bret https://electronicsarea.com/continuity-tester-using-741-ic/#comment-387996 Sun, 01 Jan 2023 22:39:38 +0000 http://electronicsarea.com/?p=2926#comment-387996 Not a bad piece to have around the bench or shop but if it were me, I’d prefer the LED to be green indicating a good connection and a to illuminate only when a connection is good. A red green dual LED would be nice to indicate red for open and green for closed circuit. Red on till circuit connection is good then switch to green. I’m going to try to make this basic circuit but add in a NPN and PNP to the output to switch the LED from Red to Green.

]]> Comment on Bike Flashing LED Lights Circuit by Marcel https://electronicsarea.com/flashing-led-bike-lights-circuit/#comment-52592 Fri, 17 Jan 2020 19:53:58 +0000 http://electronicsarea.com/?p=1337#comment-52592 Hello Jim

The circuit is energized by connecting the positive terminal of the 9-volt battery to the upper terminal of R1 and the negative terminal to the lower terminal of C1.

Regards

]]> Comment on Audio Splitter Circuit Diagram – 1 Input – 4 Outputs by Marcel https://electronicsarea.com/1-input-4-outputs-stereo-audio-splitter/#comment-47509 Thu, 05 Dec 2019 20:25:30 +0000 http://electronicsarea.com/?p=3493#comment-47509 Hello Yhen

+12V must be connected to Pin 4 and -12V must be connected to Pin 11 of the LM324

Regards

]]> Comment on Bike Flashing LED Lights Circuit by Jim https://electronicsarea.com/flashing-led-bike-lights-circuit/#comment-44561 Mon, 11 Nov 2019 07:20:39 +0000 http://electronicsarea.com/?p=1337#comment-44561 Where do you set the power source though?

]]> Comment on Autotransformer by Akhil https://electronicsarea.com/autotransformer/#comment-34033 Fri, 09 Aug 2019 13:31:35 +0000 http://electronicsarea.com/?p=73#comment-34033 Super

]]> Comment on Tone generator using two 555 timers by Marcel https://electronicsarea.com/tone-generator-using-two-555-timers/#comment-31867 Mon, 13 May 2019 23:16:15 +0000 http://electronicsarea.com/?p=3367#comment-31867 Hi Eric

Thanks for notifying me of the error. I have already done the correction to the tutorial.

Thank you

regards

]]>